Capitol Equipment
NewEagleFintecCemcoApplicationsContactUsed
<< Back to Used

2000 EAGLE 1400-45 OC PORTABLE CRUSHING PLANT


2000 EAGLE 1400-45 OC PORTABLE CRUSHING PLANT


Receiving Hopper: heavy-duty, structural steel reinforcement of side plates, 8' x 19'2" top opening;

 

Vibrating Grizzly Feeder: 57" x 18' lg., includes 60" tapered step grizzly of nominal 2" bar spacing, 25 HP, 1200 RPM, TEFC, electric motor drive, mounted as integral part with hopper on common base;

Horizontal Shaft Impactor: Eagle UltraMax 45 Primary/Secondary, weight 38,700 lbs., 35" x 56" feed opening, exclusive fixed bar solid steel sculptured rotor, cast primary curtain, fabricated secondary curtain with wear resistant replaceable liners, hydraulic shim adjustment on secondary curtain, crusher housing split with gas powered hydraulic opening for access to rotor, curtains and replaceable liners;

Grizzly Fines Conveyor: 24” wide, reversible for discharging grizzly by-pass material to grizzly transfer conveyor, 20º troughed picking idlers, full length skirtboards, 4 HP, motorized head pulley motor drive;

Grizzly Transfer Conveyor: 24" wide, pivot mounting for either side of plant, 20º troughed picking idlers, full length skirtboards with receiving hopper, 4 HP, motorized head pulley;

Undercrusher Discharge Chute: heavy-duty steel reinforced plate with 1" abrasion resistant steel replacement liners;

Platforms and Railings: heavy-duty tread plate design with access ladders to the platforms from either side of plant. Platforms and railings located at the crusher, diesel, and at the hopper for operation;

Main Trailer Frame: 18" wide flange beam side rails, tri-axle suspension with 114" track axles, twelve 11:00 x 22.5 12-ply tires, air controlled brakes with emergency and service gladhands, fifth wheel plate and kingpin, pre-wired running lights with stop, directional and three light marker bar;

Plant Support System:   Two (2) front "stiff-leg" hydraulic cylinders controlled by gasoline-powered hydraulic unit complete with in-line load controls on each cylinder and directional control valves;

Drive Guards: formed sheet metal with wire mesh complete with hinge type doors for easy access to pulleys and belts;

Central Control Panel:    NEMA 4 type box, mounted on self supporting structure complete with circuit breaker, transformer, motor starters and fuses, emergency stop pushbutton, four starters and fuses with quick disconnect plugs for radial stackers, starters and fuses with quick disconnect plugs for all additional motors on 3 deck screen, one dual 110 volt plug for scales or variable speed heater only.  Remote operator's pendant complete with all start/stop and emergency stop pushbuttons;

Electric Power: 300 HP, 1800 RPM, TEFC, electric motor drive with a 400 HP reduced voltage starter in a NEMA 4 style box mounted on self supporting structure.

Portable Discharge System: (S/N 22110) includes belt protecting gathering hopper with 400 Brinell replaceable liners, 42" x 40' channel frame type conveyor, impact absorbing slider bed with laminated impact rails at loading area, 20º troughing idlers, 10 feet of skirtboard with rubber flashing, 15 HP, 1800 RPM, TEFC, electric motor drive, heavy duty conveyor frame with 71" track axle and two 11:00 x 22.5, 12-ply tires, lunette eye tongue.

Magnetic Separator: Dings Model 33CR continuous belt magnet with stainless steel clad discharge belt, 5 HP, 1800 RPM, TEFC, electric motor drive, magnet rectifier converts AC voltage to DC voltage.

 

UPDATES TO EAGLE 1400-45 OC PLANT:

 

1

New tires

2

New Grizzly weldment

3

Rebuilt feeder/hopper with new liners

4

New wear liners in feeder

5

New safety chains at feed hood

6

New Primary curtain

7

New spindles for primary curtain

8

All new liners for secondary curtain

9

Replaced approx 90% of linersin impactor and discharge box

10

Replaced main breaker in main electrical panel

11

Replaced panel box for reduced voltage starter for 300 HP motor

12

Replaced operators remote panel and control cable for that panel

13

Rebuilt rectifier panel for magnet with new panel box and cable

14

Resealed leaking cylinder for impactor door

15

Resealed two run on cylinders

16

Replaced most of the expanded metal on doors for belt guards

17

Hardfaced rotor as necessary

18

Sand blasted, primed and painted plant


Subject to prior sale: "AS IS, WHERE IS".

PRICE FOR ABOVE.............. $235,000

<< Back to Used