Capitol Equipment
NewEagleFintecCemcoApplicationsContactUsed
<< Back to Used

2011 EAGLE 1400-45 CC

UPDATED PHOTOS TO FOLLOW:

 

USED 2011 EAGLE  ULTRAMAX 1400-45 CC PORTABLE PLANT W/3 DECK SCREEN

 

HOURS: +/- 2,500

 

Plant s/n 31086     Impactor s/n 31087     Triple Deck Screen s/n 31095     42” Discharge Conveyor s/n 31088                                

 

Receiving Hopper: heavy-duty, structural steel reinforcement of side plates, 8'0" x 19'1" top opening;

 

Vibrating Grizzly Feeder: 57" x 18’ lg., includes 60" tapered step grizzly of nominal 2" bar spacing, 25 HP, 1200 RPM, TEFC, electric motor drive, mounted as integral part with hopper on common base;

 

Transition Hood: Consisting of a heavy duty fabricated feed chute with chain designed to accommodate vibratory-type feeding mechanisms and spraybar for dust suppression;

 

Horizontal Shaft Impactor: Eagle UltraMax 45 primary/secondary, Wt. 40,000 lbs., 35" x 56" feed opening, exclusive fixed bar solid steel sculptured rotor, cast primary curtain, fabricated secondary curtain with wear resistant replaceable liners, hydraulic shim adjustment on secondary curtain, crusher housing split with hydraulic opening for access to rotor, curtains and replaceable liners;

 

Blowbar Removal Tool: A lifting device for removing or flipping blowbars with lifting eye.

 

Undercrusher Discharge Chute: heavy duty steel reinforced plate with 1" abrasion resistant steel replacement liners, also included is baffle plate with replaceable liners to control flow of material onto discharge conveyor;

 

Platforms & Railings: heavy-duty tread plate design with access ladders to the platforms from either side of plant. Platforms and railings located at the crusher, engine, and at the hopper for operation;

 

Main Trailer Frame: 24" wide flange beam side rails, air ride tri-axle suspension with 114" track axles, twelve 11:00 x 22.5 14-ply tires, air control brakes with emergency and service gladhands, fifth wheel plate and kingpin, prewired running lights with stop, directional, and 3 light marker bar;

 

Plant Support System: set of 4 “stiff-leg” hydraulic cylinders controlled by gasoline-powered hydraulic unit complete with in-line load controls on each cylinder and directional control valves;

 

Drive Guards: formed sheet metal with wire mesh complete with hinge type doors for easy access to pulleys and belts;

 

Central Control Panel: NEMA 4 type box, mounted on self supporting structure complete with circuit breaker, transformer, motor starters and fuses, emergency stop pushbutton, four starters and fuses with quick disconnect plugs for radial stackers, starters and fuses with quick disconnect plugs for all additional motors on 3 deck screen, one dual 110 volt plug for belt scale only.  Remote operator’s pendant complete with all start/stop and emergency stop pushbuttons;

 

Fines Bypass Chute: has a flop gate for diverting material from grizzly to the under-crusher gathering hopper or to jump conveyor for stockpiling.

 

Diesel Power: 510 Cont. HP rated @ 1800 RPM, electronic controlled governor, PTO, emergency shutdown system for low oil pressure, overspeed and high temperature, dual 125 gallon fuel tanks;

 

Generator:  Heavy-duty base mounted, 175 KW, 460 volts, 3-phase, 60 hertz.\

 

Generator Enclosure: welded structure with turbo pre-cleaner, which protects generator from asphalt dust.

 

Portable Discharge System: Includes belt protecting gathering hopper with 400 Brinell replaceable liners, 42" x 40' channel frame type conveyor, impact absorbing slider bed with laminated impact rails at loading area, 20° troughing idlers, full length skirtboards with rubber flashing, 15 HP, 1800 RPM, TEFC, electric motor drive, heavy duty conveyor frame with 71.5” track axle with two 11:00 x 22.5 14-ply tires, burned plate tongue. (NOTE: On site portable only).

 

Vibrating Pan Feeder for 42” Discharge Conveyor.

 

Magnetic Separator: Dings Model 33CR continuous belt magnet with stainless steel discharge belt, 5 HP, 1800 RPM, TEFC, electric motor drive, magnet rectifier converts AC voltage to DC voltage.

 

Spring Bridge: primary curtain spring bridge assembly where each spring exerts a compressive force for additional stabilization of primary curtain and still allows to swing away under extreme loads, such as uncrushables, with hydraulic adjustment.

 

Bolt-in Grizzly Plates: steel plates for covering grizzly section.

 

 

 

 

Eagle Portable 6 x 20 Screening Plant:

 

Screen:  6’ x 20’ horizontal triple deck screen, 50 HP, 1800 RPM, TEFC, electric motor drive.

 

Integral Feed Conveyor: 45” x 28’ channel frame type, 20 troughing idler, lagged head pulley, winged tail pulley, large receiving hopper, full length skirtboards with rubber flashing, 15 HP, 1800 RPM, TEFC, electric motor V-belt drive and guard;

 

Fines Conveyor: 60” x 22’ frame integral type, flat idlers, lagged head pulley, winged tail pulley, 10 HP, 1800 RPM, TEFC, electric motor V-belt drive and guard;

 

Walkway:  24” with toe board and handrails on each side of screen;

 

Reversible Discharge Chutes: easy discharge of top deck and second deck material;

 

Fines Cross Conveyor: 36” x 10’ reversible cross conveyor for discharge of fines material with 10 HP internal drive head pulley;

 

Maintenance Platform: on side of screen with guarding for plant, feed conveyor included.

 

Underscreen Gathering Hopper: for collection of fines material through third deck of screen and discharge onto 60” fines conveyor;

 

Main Frame: heavy-duty wide flange beam, air ride tandem axle with eight 11R 22.50, 14-ply tires, air controlled brakes with emergency and service gladhands, fifth wheel plate and kingpin, pre-wired running lights with stop directional indicators;

 

Electric Motors: all pre-wired with cable to reach the main power source of crushing plant and fabricated cable wrap holders.

 

Hydraulic Lift/Leveling: set of four hydraulic cylinders controlled by independent powered hydraulic unit complete with in-line load controls on each cylinder and directional control valves.

 

Closed Circuit Conveyor: 30" x 50' portable conveyor with 24" deep truss frame, rubber cleated belting, rigid axle with manual swivel wheels and 11R 22.5-ply tires, manual raise and lower, gathering hopper, pintle hitch, 10 HP, 1800 RPM, TEFC, electric motor drive, prewired with 150' of cable from tail. (NOTE: On site portable only).

 

Portable Radial Stackers:  (2) - 30" x 50' with 24" deep truss frame, rigid axle with manual swivel wheels and 11R 22.5 tires, manual raise and lower, gathering hopper, pintle hook, 15 HP, 1800 RPM, TEFC, electric motor drive, prewired with 150' of cable from tail. (NOTE: On site portable only).

 

Subject to prior sale: "AS IS, WHERE IS".

PRICE FOR ABOVE F.O.B. BUFFALO, NY...$585,000
<< Back to Used